CGI Bathroom Remodeling Nationwide

CGI Bathroom Remodeling: The Pomona Owner’s Guide

CGI bathroom remodeling in Pomona typically runs $9,000-$28,000 for a full replacement, and we stock CGI-compatible fixtures, enclosures, and hardware across our most common Pomona model lines. Most Pomona homeowners discover their CGI system needs attention when the shower door track starts binding, the acrylic surround shows stress cracking near the drain, or the original silicone seals have hardened past the point of resealing. We carry the replacement tracks, rollers, and panel gaskets on our trucks for same-day repair when the failure is isolated to a single component.

Call (626) 606-1081

Which CGI Models This Applies To

CGI has produced several enclosure series over the past two decades, and the part you need depends on whether you’re working with a framed, semi-frameless, or frameless system. The most common units we service in Pomona are the Classic Series (framed, 3/16″ glass, top-hung rollers), the Elegance Series (semi-frameless, 1/4″ glass, through-glass pivot hinges), and the Premier Series (frameless, 3/8″ or 1/2″ glass, wall-mount hinges with brass or stainless bushings). Check the lower corner of your door panel or the header rail for a stamped model code; if it’s worn off, measure the glass thickness with a caliper and photograph the hinge or roller profile. OEM rollers and hinges from CGI are still available for most discontinued lines, though we also source equivalent-grade hardware from CRL and Prime-Line when the OEM lead time stretches past what a functioning bathroom can tolerate. The aftermarket equivalent is usually indistinguishable in function, but we verify bushing diameter and roller offset to the millimeter before installing - a 3/4″ roller in a 7/8″ track will chatter itself to pieces in six months.

Signs Your CGI Bathroom Remodeling Is Failing

• Door binding or jumping the track. The nylon rollers have flattened or the axle pin has corroded, usually from hard water deposits that Pomona’s municipal supply deposits aggressively. Left alone, the door will eventually derail and chip the glass edge.
• Water pooling outside the enclosure after a shower. The vertical vinyl seals have shrunk or the bottom sweep has lost its flex. In framed units, the drip rail may also be clogged with calcium buildup, redirecting water inward.
• Stress cracks in acrylic or fiberglass surrounds. These start at the drain flange or corner seams where the substrate has flexed. Pomona’s clay-heavy soil shifts seasonally, and that movement transmits through the slab to the shower pan if the bed wasn’t floated properly at install.
• Hinge squeal or door sag. The brass or stainless bushings in the pivot hinge have worn oval, or the through-bolts have loosened from the wall backing. Frameless doors over 28″ wide will sag noticeably once the hinge loses even 1/16″ of integrity.
• Discolored or missing grout/caulk at the tile-to-tub joint. This is less a CGI part issue than a system failure - water is getting behind the surround and will eventually degrade the wallboard. We see this most in Pomona’s post-war bungalows where the original plaster lath meets a retrofitted enclosure.

Before

After

Replacement Cost & What’s Included

A full CGI bathroom remodel in Pomona runs $9,000-$28,000, with the final number driven by whether we’re replacing the enclosure only or gutting to the studs. Component-level repairs are far narrower: a roller and track replacement typically falls between $400-$900, hinge rebuilds run $350-$750, and a complete glass-and-hardware swap on an existing footprint averages $2,500-$5,500. Our quotes are flat prices with written scope - under Clause 1 of the Haven Standard, the number you sign is the number you pay, and no change proceeds without a signed change order. Every repair includes a documented photo record of the before condition, the opened cavity, and the finished work. We warranty our installation for 365 days under the Done Right Promise; hardware and glass carry the manufacturer’s warranty, which we register on your behalf.

DIY or Call Us?

There’s a safe middle ground here. A homeowner can inspect the roller condition, clean the track with vinegar, and verify that hinge screws are tight - but stop there. Frameless glass panels weigh 80-120 pounds each, and the torque on a 3/8″ door hinge is enough to shear a misaligned anchor clean out of the stud. We’ve been called to Pomona jobs where a well-intentioned owner cracked a $900 panel trying to rehang it solo. The other gotcha is waterproofing: if your repair exposes the substrate, you need a proper vapor barrier and flood test before tile or surround goes back. That’s not a weekend project. Measure twice, then we can talk. Call (626) 606-1081 and we’ll scope it in person, no charge for the estimate.

FAQs