Jerith Driveway & Pavers Nationwide

Jerith Driveway & Pavers: The Pomona Owner’s Guide

We stock and install Jerith-compatible driveway and paver components for Pomona homeowners, with typical installed replacement costs running $500-$2,400 depending on the scope and substrate condition. Most Jerith paver resets and edge-restraint repairs can be scheduled within 48 hours, and we carry common Jerith-compatible edge profiles and bedding compounds on our trucks. In Pomona, we usually get the call after a homeowner notices the driveway surface shifting near the garage apron or after the first heavy winter rain exposes drainage gaps that weren’t visible in August.

Call (626) 606-1081

Which Jerith Models This Applies To

Jerith does not manufacture pavers directly; the brand is known for aluminum fence and ornamental metalwork, so “Jerith driveway and pavers” in practice refers to paver installations that border Jerith fencing systems or integrate with Jerith gate hardware on Pomona properties. The parts we match are the paver edge restraints, bedding sand profiles, and drainage channel components that interface with Jerith fence posts and gate footings. To identify what you need, check the post base plate dimensions - Jerith standard residential posts use 4×4 or 6×6 base plates with 1/2-inch anchor bolts on 3-inch centers, which dictates the paver cut pattern and edge restraint spacing.

We source OEM-compatible edge restraints from Belgard and Techo-Bloc, both of which publish spec sheets matching Jerith post footprints. Aftermarket equivalents from these brands typically run 15-20% less than custom-fabricated metal edging and carry the same 25-year residential warranty against cracking in freeze-thaw cycles. One compatibility gotcha: Jerith’s commercial-grade Estate series uses wider 8×8 base plates that will overcut standard paver soldier courses by two inches unless the layout is adjusted at the design stage. We’ve rebuilt three Pomona driveways near Ganesha Park where this was missed during initial installation.

Signs Your Jerith Driveway & Pavers Is Failing

• Edge pavers tilting outward at the fence line. The plastic or aluminum edge restraint has cracked or pulled its stakes, usually because Jerith post footings were poured too close to the paver bedding layer and the concrete expansion pushed the restraint outward. In Pomona’s clay-heavy soils near the 71 corridor, this accelerates after wet winters.
• Standing water along the gate track after light rain. The bedding sand has washed out from beneath the pavers, creating a low spot where water collects against the Jerith gate hardware. The underlying cause is almost always a missing or clogged drainage channel between the paver field and the fence footing.
• Pavers rocking underfoot near post bases. The bedding layer has compacted unevenly because the original installer didn’t account for the load concentration from Jerith gate posts. This is a structural bedding issue, not a paver defect, and it worsens with every vehicle pass if the gate is in a driveway turnaround.
• Sand joints disappearing between pavers within two feet of fence posts. The vibration from gate operation - particularly heavier Jerith Estate-series gates - shakes fine jointing sand out of the joints. Polymeric sand usually solves this, but only if the bedding is stable first.
• Visible gap opening between paver edge and fence post base plate. The paver field and the Jerith footing are moving independently, which means the original installation lacked an isolation joint or expansion buffer. In Pomona’s inland climate, the daily temperature swing between 55°F and 90°F from March through November makes this gap grow measurably within a single season.

Before

After

Replacement Cost & What’s Included

For Jerith-adjacent paver work in Pomona, partial edge-restraint replacement runs $500-$1,200, while full paver reset with corrected bedding and drainage typically falls between $1,800-$2,400. The range depends on linear feet of edge restraint, whether we need to remove and re-lay existing pavers or match new ones, and whether the Jerith post footings themselves need re-pouring to create proper drainage fall.

Every quote we write itemizes parts and labor separately: edge restraint material by the foot, bedding sand by the ton, polymeric jointing sand by the bag, and crew hours at a flat rate. Under Clause 1 of the Haven Standard, that written price is locked before work starts. Our paver resets carry a 365-Day Done Right Promise on workmanship, and we document the before condition, the substrate exposure, and the finished grade with a photo record you receive before we leave. No change to the scope - not even adding ten extra feet of edge restraint - proceeds without a signed change order.

DIY or Call Us?

There’s no high-tension danger in paver work the way there is with garage door springs, but there’s plenty of ways to make the problem worse. An owner can safely check whether the edge restraint stakes are still seated or whether jointing sand is washing out - those are visual inspections that cost nothing. Where DIY goes wrong is in re-bedding without addressing the Jerith post footing that’s causing the displacement. We’ve been called to Pomona jobs where a homeowner rented a plate compactor, added an inch of sand, and relaid the same pavers only to watch them shift again in six weeks because the gate post was still heaving.

Measure twice, then we can talk. If you’re seeing any of the symptoms above, call us at (626) 606-1081 and we’ll schedule a free estimate with a written scope and price before any work starts.

FAQs